The mould designs a standard

Standard of use FUTABA standard structural group model. 2.

Use steel or with spare parts of standards standard mould, fittings. 3.

All guiding annul (GUIDEPIN) , lining (BUSHING) there must be protruding in tail end model. 4.

Face paper size needs all mould blueprint dimension of norms of unified use a standard-sized sheet, after waiting for approve, just begin to make. 5.

When part of the finished product on the mould is machined, the half value of public errand of the dimension in answering to pursue with finished product comes as treatment public errand, the common difference that must not use finished product graph to go up will machine. 6.

All magnanimity unit with imperial to allow, length uses millimeter, weight is used kilogram, temperature is used centigrade (C) . 7.

Pressure is an unit with imperial PSI, 1PSI=1 pound / square inch =14.

2 kilograms / square centimeter. 8.

Affirm the model is large, place pattern plate journey, the top gives the route. 9.

Fair master mold position of opening of model of 4 flank condole, "A " " B " board two side have each photograph neighbour the least aperture of one condole model, other pattern plate has a side face to have condole model opening the least. 10.

4 guide the either in selling is raised, must make it is prejudicial, namely not rather 3 his semmetry, combine a model in order to prevent fair, master mold reversely. 11.

Norms of the rolled steel that print reachs underside of hardness Wu Moren. 12.

Detailed lists material to express indicative material and finishing norms, indicative electric heat implement wattage norms and voltage size. 13.

Print, number is all mould spare parts. 14.

Mould two flank, should with secure with bar before case, lest modular face is apart. 15.

When acupuncture point of model of same finished product exceeds an acupuncture point, so that identify modular acupuncture point,should use serial number. 16.

In the model on need to Kong Wumo of one condole model has centre of gravity place, tilt in order to avoid the mould when condole model, decide enough bear model weighs whorl and deepness. 17.

Outside dividing modular benevolence to bedding face accumulates ladder rank to rely on to defeat, all answer lock of device model face is decided piece (PARTINGLINELOCKS) . 18.

Costal region piece when deepness exceeds 5mm, need to add ease to gas is sold or be made with mold insert at costal region bottom, with benefit plastic fill up. 19.

When doing plane to rely on to defeat with peg, should extend peg top lengthen rolled steel inside, avoid peg to end face controls damage or be out of shape. 20.

Finished product is main place, should a bit obligate dimension, avoid to machine dimension too big and bring about filling solder. 21.

Modular benevolence prohibits filling weld without the license. 22.

When with filling below special situation solder repairs a mould, should choose a mould to become welding rod with material, lest material pledges,the exterior of distinct effect finished product is reached leave a mark. 23.

Each are assembled group stand to all should control tolerancepublic errand really, the mark that must not have beat stays. 24.

All pattern plate divide the side that distribute a model outside, the others corner should pour wine cup. 25.

Use electric heat implement mould, all need to add circuit to so that produce an unit,pursue correct wiring. 26.

When the mould needs to bite beautiful processing, unplug modular angle needs 2 degrees of above at least, deepness gnawing a flower criterion every are deep 0.

001 " need to increase 1 degree to unplug modular horn, for example: Deepness is 0.

003 " when need to 5 degrees unplug modular angle, surface of acupuncture point of the model before biting a flower should make light with #300 sand paper at least. 27.

Confirm modular acupuncture point, model strength is enough. 28.

Mould design should accord with annotations of face of finished product graph to ask. 29.

Offer all do not attribute standard norms part detailed picture face. 30.

After modular benevolence surface is handled via eletroplating, should heat modular benevolence heats 1 hour to calculate with 1 inch of ply to 500F, in order to prevent modular benevolence fragile change. 31.

Eletroplate ply and adherent intensity all require special attention, there must not be the appearance that flake after use. 32.

Plastic machine top gives beautiful form lever location drawing, advocate design of barb of makings head extreme, reach 3 models or use pare barb of design of beard of design of its pull rod asks makings board mould. B.

Mould group establishs a graph to make a point [one] view of master mold plane wants indicative part 1.

Indicative master mold is all and basic dimension. 2.

Size of hole of indicative pattern plate, model benevolence, model benevolence, the position. 3.

Designation secures screw, fixed position sells the position. 4.

Designation places modular channel dimension, the position. 5.

Indicative ease enrages channel, modular side is practical interface dimension, the position. 6.

Designation is inclined annul, slide block, position of oil pressure crock. 7.

Measure of indicative conduit return, the position. 8.

Indicative makings channel, present glue opening, heat shoots mouth position, dimension. 9.

Indicative model face secures a dimension. 10.

Use section plane to convey need to make its are clear about more clearly partly as far as possible. 11.

Mould quadrilateral dimension of prize model channel is 45 degrees of X6mm deep. [2] view of common standard plane wants indicative part 1.

Indicative top gives a system all and basic measure. 2.

Indicative roof length and width dimension. 3.

Designation secures screw position. 4.

The top on indicative motherboard gives aperture measure, the position. 5.

Indicative top goes out board on screw, fixed position sells the position. 6.

Measure of indicative conduit return, the position. 7.

Designation places modular channel dimension, the position. 8.

Position of thimble of face of designation common standard. 9.

Indicative pattern plate, modular benevolence, size of modular benevolence hole, the position. 10.

Designation is inclined annul, slide block, dimension of oil pressure crock, the position. 11.

Indicative model face secures a dimension, the position. 12.

Indicative top gives systematic measure, the position. 13.

Designation takes glue mouth measure, the position. 14.

Designation is answered sell measure, the position. 15.

Hole of model of roof hang oneself is the smallest dimension 10mm-16X2 aperture. 16.

Use 50mm diameter common standard to prop up column as far as possible, 70mm diameter is used to prop up column when exceeding 500mm like mould length, to make stress of obligate of fair pattern plate, height of the intermediate position post that prop up should prop up column than other position tall 0.

05mm. [3] part of section plane view 1.

Dimension of ply of indicative pattern plate. 2.

Measure of indicative conduit return, the position. 3.

Screw of the 6 horn inside the smallest use M12 or larger size secure pattern plate. 4.

Modular benevolence and model benevolence acupuncture point is calculated by the face that distribute a model at least case 12mm-20mm deepness cooperates to tighten. 5.

Modular benevolence should compare pattern plate tall 1mm (the smallest) - 0.

5mm (the biggest) . 6.

Guide sell length to grow 20mm than apogee of common standard face the least. 7.

Indicative mould overall length needs to spend on view, overall width. 8.

Indicative and all model answers on graph face benevolence, top piece, inclined annul, slide block, dimension of oil pressure crock, the position. C. Makings head lining (SPRUEBUSHING) , fixed position is sold (LOCATINGRING) 1.

Use FUTABA or with lining of head of norms dimension makings, fixed position is sold. 2.

Dimension of mouth of indicative makings head reachs 20R ball way. 3.

External diameter of fixed position annulus is 100mm diameter. 4.

Length of makings head lining with exceeding 75mm advisable, if A board ply exceeds 75mm, need to will expect head lining is immersed in pattern plate inside, make expect head lining length is in as far as possible 75mm less than. 5.

Use M6-20 screw or diametical 6mm fixed position sell lining of fixed makings head. D. Makings channel (RUNNER) , the mouth that enter glue (GATE) part. 1.

Use circle makings channel as far as possible. 2.

Indicative makings channel, present glue opening, makings channel and measure of gap of the mouth that enter glue. 3.

Lie between makings board (RUNNERBARS) require heat treatment. 4.

In makings channel extreme due cold makings channel (COLDSLUGS) . 5.

Bright show finished product where to enter glue, in order to avoid an effect finished product exterior and assemble a worry. 6.

When using bit to present glue opening, if mould structure allows,answer to be used in master mold pare makings board in order to ensure advocate makings head is broken away from. 7.

The mouth that enter glue and makings channel all need to make light. 8.

In makings channel extreme should add ease to enrage channel. 9.

The design ginseng of all sorts of glue mouths designs a standard according to groovy mould. 10.

Sort of the mouth that enter glue uses on the mould: 1.

Disc type (DIAPHRAGM) 2.

Bit type (PIN) 3.

Type of makings head straight fill (SPURE) 4.

Sector type (FAN) 5.

Protruding piece type (TAB) 6.

Filmy type (FILM) 7.

The type that press a knife (EDGE) 8.

Conceal type (SUBMARINE) 9.

Pin mark type (PINPOINT) D. The top gives systematic part to ensure finished product supports appropriately, character of shrink of finished product material must consider when designing a pattern, pare expecting board top gives a system is best means, because pare makings board can be balanced effective top gives finished product, when going out to prevent a top, finished product generation is out of shape, screwy, thimble should be placed in the wall thicker, costal region (RIB) , columnar (BOSSES) the position. 1.

Use FUTABA or with norms dimension thimble and thimble bushing. 2.

Do not get the following thimble of use 2mm diameter, unless special appoint. 3.

All thimble and bushing, fall in modular face only 20mm-30mm deepness slides to tighten cooperate, meantime is unoccupied place for 0.

02mm. 4.

Tightening slip outside cooperating an area, thimble and clearance of fair pattern plate are 0.

5mm, it is 1mm with clearance of common standard backboard. 5.

Thimble aperture should use the treatment that wring a knife, in order to ensure inside aperture surface is slick, smooth. 6.

Thimble should take 2mm above rolled steel at least all round aperture. 7.

All thimble head needs to be the same as plane absolutely with thimble cover board. 8.

Thimble must not exceed common standard range, the biggest common difference is low defect 0.

05mm. 9.

All blame make the same score the thimble of surface contact, all need to secure its tail end and prevent to rotate. 10.

Indicative roof journey is apart from dimension. 11.

Indicative roof fills up button (STOPBUTTONS) , every raise roof area 200 square area increases a roof to fill up button to go up at backboard. 12.

Use 4 protruding to larger size mould model guide annul with lining, narrower to width length does not exceed 300mm roof to be able to use 2 protruding model guide annul with lining guiding the top gives a system. 13.

Use 4 to answer at least annul, mould length exceeds 600mm above to need to use 6 to answer annul. 14.

Secure thimble cover board and roof screw amount, with millimeter of every 200 square a screw is calculated. 15.

Roof the reverse side attacks a tooth to produce forming machine ejector pin in order to cooperate, stage of 200 the following machine attacks M10, stage of 200 above machine attacks M16. 16.

Hit in finished product when thimble all round half makings when, should cooperate roof in advance to return an unit, lest thimble hits area of master mold model, when finished product material is ABS, PC, HIPS, use 6mm (the smallest) thimble, material is PP, 10mm thimble is used when PE, material is PVC. KRATON uses 12mm thimble. 17.

When use bushing top goes out, the heart sells applied pressing plate to be secured by impaction of the reverse side of common standard motherboard, bushing heart is sold should use standard norms thimble. 18.

On finished product hollow cylinder, all need to go out with bushing top. 19.

Avoid to use thimble of fixed position type as far as possible, d form head is used to secure thimble as far as possible when must be being used. 20.

All thimble and thimble bushing all answer number, so that identify, assemble. 21.

The top gives finished product place to require thimble amount, can calculate by formula, the mould that joins as usual plan designs a standard. E. Cooling bribery part 1.

With plane, section plane inspects icon to show cooling return measure, the position. Divide special outside appointing, all conduit internal diameter is in charge of a tooth for 10mm and NPT (be not metric PT tooth) , cooperate commonly used norms fast connect, water hole should be apart from finished product at least 12mm, be apart from little 6mm of thimble Kong Zhi. 2.

Fair, master mold benevolence wants cooling return, unless special appoint, do not answer to cool on pattern plate only, but beryllium matrix benevolence except. 3.

Print " IN " , "OUT " earmark and number are entered at conduit, export position. 4.

Indicative and all O-RING and dimension of head of a place of strategic importance, the position. 5.

O-RING only the place of water hole joint of applicable Wu Chuizhi, must not use at joint of horizontal water hole to be in. 6.

The current inside indicative loop changes way. 7.

Products of copper of application of the clapboard in loop or stainless steel piece, pour horn to be assembled with benefit in top. 8.

When should using completely hot type to heat up glue road system, o-RING cannot be used in loop of refrigeration of master mold side. 9.

Conduit access position, must rely on to enter finished product wall thick thicker with bulgy content position. 10.

Distance of the center between conduit and conduit cannot be less than 30mm. 11.

When the bushing type refrigeration that should use commonly used norms covers a cooling model heart, must affirm whether contact position has use stop discharge belt, and locking fixed position. 12.

All conduit loop must pass 60 empty baric force to check, whether does the examination have flat phenomenon to happen. 13.

Clip avoids to have conduit contact near modular channel. 14.

Avoid conduit connect position to be in position of mould end face, if indispensable when, barrel-drain 12mm must be done between end face conduit and cent model face. 15.

Any linear conduit length must not grow too, bring treatment difficulty. 16.

Conduit connect and conduit joint can use silver-colored solder. 17.

15 must not exceed to turn inside loop of any a conduit dot, (4 are shared to turn when use clapboard dot) . 18.

Clapboard top and water hole should maintain the space that has way of Kong Zhi of a water. 19.

The snail tooth of conduit and connect cooperates to need close together, attack tooth deepness, silk attacks dimension to reach stop discharge belt must be chosen cautiously, the head of a place of strategic importance that closes dead end also is not gotten somewhat leak. 20.

Cooling loop designs the standard, mould refrigeration computation is formulary, conduit receives mouth norms, reach O-RING device to design groovy mould to design a standard. F. Movable type mold insert, the part such as slide block 1.

The movement of slide block grinds the face all needs to become channel of X face butter. 2.

Use inclined when selling, the ability after should deciding slide block parts in modular face begins to slide, inclined annul should use guide sell norms to make. 3.

Slide block should contain fixed position bead and bedspring, ensure to after slipping, locate. 4.

Slide block bottom should install heat treatment wear-resisting board. 5.

Use pressing plate is fixed, guide slide block. 6.

Stress of slide block design is begged tear open outfit is easy, so that can be overhauled on forming machine. 7.

When combining a model, thimble and slide block have collision to use use return an unit before. 8.

Slide block bulk and photograph of finished product bulk compare under 20: 1 when, criterion slide block has independent and cooling return. 9.

Journey of slide block shift, should need shift to be apart from big 3mm than place of real finished product. 10.

Inclined sell banking angle to spend spend for 10-25, unless have special appoint. 11.

The slide block when shutting a model should decide a lock by oblique plane lock, in order to ensure slide block locates. 12.

Oblique plane lock decides an oblique plane banking angle to spend should compare inclined annul point of view is old 5 degrees. 13.

When crock of use oil pressure drives slide block, pressure bears to be the smallest 2000psl(140 inside oil pressure crock kilogram / square kilogram) 14.

Slide block and inclined market a design, the pattern that reference standard changes is designed. CNC Milling CNC Machining